A rectifier tube has one job: turn the AC from the power transformer into DC for the rest of the amplifier. It does that job with a lot more personality than a silicon diode. It brings the B+ up gently, it sags under load, and its internal voltage drop decides what your B+ actually ends up being. Pick the wrong one and it will also quietly cook your power transformer. This chart lists the common full-wave rectifiers by heater voltage, shows which ones plug into a 5U4 or 5Y3 socket, and explains what changes when you swap.
How to read the tables
- Base is the RETMA basing code. Tubes with the same code have the same pin connections. Click a code to see its pin diagram.
- Heater A is the filament or heater current. This is the number that matters most when swapping, because the 5 V winding on the power transformer was sized for the original tube.
- Drop V is the voltage lost inside the tube at rated current. Lower drop means higher B+.
- Max mA is the maximum DC output current.
- Max V is the maximum AC voltage per plate (RMS) with a capacitor-input filter, the way most audio amps are built. Choke-input ratings are usually higher.
- Fits tells you which standard socket the tube drops into. † means the heater draws more current than the tube it replaces, so check the transformer first. ‡ means the base has extra internal connections, so check that the socket has nothing wired to the extra pins.
- A dash means the figure is not published or not confirmed.
5 Volt Full-Wave Rectifiers
| Tube | Base | Heater A | Drop V | Max mA | Max V | Fits | Notes |
|---|---|---|---|---|---|---|---|
| 5AR4 / GZ34 | 5DA | 1.9 | 17 | 250 | 450 | 5U4, 5Y3 ‡ | Lowest drop of the 5 V types. Cathode type, so slow warm-up. Raises B+ when it replaces a 5U4 or 5Y3. |
| 5AS4-A | 5T | 3.0 | 50 | 275 | 450 | 5U4 | Improved 5U4, sold as a 5U4-GB equivalent |
| 5AT4 | 5L | 5.5 | 30 | 800 | 550 | None | Heavy-duty. The 5.5 A heater needs its own winding. Slow warm-up. |
| 5AU4 | 5T | 3.75 | 50 | 325 | 400 | 5U4 † | High-current 5U4 |
| 5AW4 | 5T | 3.7 | 46 | 250 | 450 | 5U4 † | Long-life 5U4 |
| 5AX4-GT | 5T | 2.5 | 65 | 175 | 350 | 5Y3 † | High-current 5Y3 |
| 5AZ3 | 12BR | 3.0 | 44 | 275 | 600 | None | Compactron 5U4 (12-pin) |
| 5AZ4 | Loctal | 2.0 | 60 | 125 | 350 | None | Loctal version of the 5Y3, so it needs a loctal socket |
| 5BC3 | 9QJ | 3.0 | 53 | 300 | 500 | None | Compactron |
| 5CG4 | 5L | 2.0 | — | 125 | 350 | 5Y3 ‡ | Cathode tied to the heater, so slow warm-up |
| 5DJ4 | 8KS | 3.0 | 44 | 300 | 600 | 5U4 ‡ | Redesigned 5U4 with a higher voltage rating |
| 5R4-G / GY | 5T | 2.0 | 67 | 250 | 750 | 5U4, 5Y3 | High-voltage type. Its high drop lowers B+. |
| 5R4-GYA | 5T | 2.0 | 67 | 250 | 750 | 5U4, 5Y3 | Ruggedized 5R4 |
| 5R4-GYB | 5T | 2.0 | 63 | 250 | 900 | 5U4, 5Y3 | Ruggedized 5R4 with the highest voltage rating |
| 5T4 | 5T | 2.0 | 45 | 225 | 450 | 5U4, 5Y3 | Metal-envelope 5U4 rating on a 2 A heater |
| 5U4-G | 5T | 3.0 | 44 | 225 | 450 | 5U4 | Octal version of the 5Z3. British U52, Soviet 5Ц3С. |
| 5U4-GA | 5T | 3.0 | 44 | 250 | 450 | 5U4 | |
| 5U4-GB | 5T | 3.0 | 50 | 275 | 450 | 5U4 | Replaces the 5U4-G and 5U4-GA |
| 5V3 | 5T | 3.8 | 47 | 350 | 425 | 5U4 † | Higher-current 5U4 |
| 5V3-A | 5T | 3.0 | 42 | 415 | 550 | 5U4 | 5V3 with the heater current reduced to 5U4 level |
| 5V4-G / GA | 5L | 2.0 | 25 | 175 | 375 | 5Y3 ‡ | Octal 83-V. Low drop, slow warm-up. British GZ32. |
| 5W4-G / GT | 5T | 1.5 | 45 | 100 | 350 | 5Y3 | Low-current 5Y3, only for light loads |
| 5X4-G | 5Q | 3.0 | 58 | 225 | 450 | None | A 5U4 electrically, but with a different pinout |
| 5X4-GA | 5Q | 3.0 | 47 | 250 | 450 | None | A 5U4 electrically, but with a different pinout |
| 5Y3-G / GT | 5T | 2.0 | 60 | 125 | 350 | 5Y3 | Octal version of the 80 |
| 5Y4-G / GT | 5Q | 2.0 | 60 | 125 | 350 | None | A 5Y3 electrically, but with a different pinout |
| 5Z3 | 4C | 3.0 | 58 | 225 | 450 | 5U4 with adapter | 4-pin 5U4 |
| 5Z4 | 5L | 2.0 | 20 | 125 | 350 | 5Y3 ‡ | Metal envelope. Low drop, slow warm-up. British GZ30, Soviet 5Ц4С. |
| 80 | 4C | 2.0 | 60 | 125 | 350 | 5Y3 with adapter | 4-pin 5Y3 |
| 83 | 4C | 3.0 | 15 | 225 | 450 | Special | Mercury vapor. See the swap notes below. |
| 83-V | 4C | 2.0 | 25 | 175 | 375 | 5V4 with adapter | 4-pin vacuum version of the 83, cathode type |
| 5931 | 5T | 3.0 | 47 | 300 | 600 | 5U4 | Industrial premium 5U4 |
| 6004 | 2AJ | 2.0 | 60 | 120 | 375 | None | High-reliability 5Y3 with the plates on two top caps, so it is not a plug-in replacement |
| 6087 | 5L | 2.0 | 50 | 125 | 350 | 5Y3 ‡ | Same tube as the 5Y3WGTB, a high-reliability 5Y3. Cathode type. |
| 6106 | 5L | 2.0 | 60 | 125 | 350 | 5Y3 ‡ | High-reliability 5Y3 |
| 6853 | 8HE | 1.7 | 60 | 125 | 350 | 5Y3 ‡ |
6.3 Volt Full-Wave Rectifiers
These usually share the 6.3 V heater winding with the signal tubes. All of them are cathode types, and the cathode sits at full B+. That puts real stress on the heater-to-cathode insulation, so check the heater-cathode voltage rating against your B+ before you use one.
| Tube | Base | Heater A | Drop V | Max mA | Max V | Notes |
|---|---|---|---|---|---|---|
| 6AX5-GT | 6S | 1.2 | 50 | 125 | 350 | |
| 6AX6-G | 7Q | 2.5 | 21 | 250 | 350 | High heater current |
| 6BW4 | 9DJ | 0.9 | 40 | 100 | 325 | 9-pin miniature |
| 6BY5-G / GA | 6CN | 1.6 | 32 | 175 | 375 | |
| 6CA4 | 9M | 1.0 | 20 | 150 | 350 | Same as the EZ81 |
| 6W5-G | 6S | 0.9 | 24 | 90 | 325 | |
| 6X4 | 5BS | 0.6 | 22 | 90 | 360 | 7-pin miniature. Same as the EZ90, Soviet 6Ц4П. |
| 6X5 | 6S | 0.6 | 22 | 80 | 360 | Octal. The 6X5GT is the same as the EZ35, Soviet 6Ц5С. |
| 6Z5 | 6K | 0.8 | — | 60 | 325 | |
| 6ZY5-G | 6S | 0.3 | 18 | 40 | 325 | |
| 7Y4 | 5AB | 0.5 | 22 | 70 | 325 | Loctal |
| 7Z4 | 5AB | 0.9 | 40 | 100 | 325 | Loctal |
| 84 / 6Z4 | 5D | 0.5 | 20 | 60 | 325 | 5-pin base |
| 5852 | 6S | 1.2 | — | 65 | 300 | Premium 6X5 |
| 5993 | 9-pin | 0.8 | — | 60 | 260 | Noval base |
| 6202 | 5BS | 0.6 | 22 | 55 | 325 | Premium 6X4 |
| 6203 | 9CD | 0.9 | 22 | 77 | 325 | |
| 6325 | — | 2.7 | — | 250 | 780 | High heater current |
| 6754 | 9ET | 1.0 | — | 90 | 325 | High-reliability type |
Other Heater Voltages
Most of these come from AC/DC radios and TVs with series-string heaters, where the rectifier heater is wired in line with every other tube. They are not drop-in candidates for a hi-fi amplifier. Several of them, including the 25Z5, 25Z6 and 117Z6, have two separate cathodes and were designed as rectifier-doublers rather than conventional center-tap full-wave rectifiers.
| Tube | Base | Heater V / A | Drop V | Max mA | Max V | Notes |
|---|---|---|---|---|---|---|
| 0Z4 | 4R | None | 24 | 75 | 300 | Cold-cathode gas rectifier, used in car radios with vibrator supplies |
| 82 | 4C | 2.5 / 3.0 | 15 | 115 | 450 | Mercury vapor |
| 3DG4 | 5DE | 3.3 / 3.8 | 32 | 400 | 325 | High heater current |
| 12BW4 | 9DJ | 12.6 / 0.45 | 40 | 100 | 325 | 12.6 V version of the 6BW4 |
| 12DF5 | 9BS | 12.6 / 0.45 | 40 | 100 | 350 | |
| 12X4 | 5BS | 12.6 / 0.3 | 22 | 90 | 360 | 12.6 V version of the 6X4 |
| 25X6 | 7Q | 25 / 0.3 | 25 | 60 | 125 | |
| 25Y5 | 6E | 25 / 0.3 | — | 42 | 250 | |
| 25Z5 | 6E | 25 / 0.3 | 22 | 75 | 235 | Rectifier-doubler |
| 25Z6 | 7Q | 25 / 0.3 | 22 | 75 | 235 | Rectifier-doubler |
| 26Z5 | 9BS | 26.5 / 0.2 | 22 | 50 | 325 | |
| 28Z5 | 6BJ | 28 / 0.24 | 40 | 100 | 325 | |
| 50AX6-G | 7Q | 50 / 0.3 | 21 | 250 | 350 | |
| 50X6 | 7AJ | 50 / 0.15 | 22 | 75 | 235 | |
| 50Y6 | 7Q | 50 / 0.15 | 22 | 75 | 235 | |
| 50Y7 | 8AN | 50 / 0.15 | 22 | 75 | 235 | |
| 50Z6 | 7B | 50 / 0.3 | — | 75 | 235 | |
| 50Z7 | 8AN | 50 / 0.15 | 21 | 65 | 235 | |
| 117Z6 | 7Q | 117 / 0.075 | 15.5 | 60 | 235 | Rectifier-doubler, heater runs straight off the line |
| 5690 | — | 12.6 / 1.2 | 17 | 125 | 350 | High-reliability type |
Before You Swap a Rectifier
The safest replacement is always the same tube number the amplifier was designed for. If you want to substitute, whether to change the sound, lower the cost or get something you can actually buy, check these points in order:
- Heater current comes first. The 5 V winding was sized for the original tube. A 5U4 (3 A) in a 5Y3 socket (2 A) overloads the winding, and the transformer runs hot and can fail. Going the other way, with a 2 A 5R4 or a 1.9 A GZ34 in a 5U4 socket, only makes the winding run cooler.
- Voltage drop sets your B+. At rated current a GZ34 drops about 17 V, a 5U4-G about 44 V and a 5Y3 about 60 V. Put a GZ34 in a 5Y3 amp and B+ can rise by roughly 25–45 V depending on the load. Check the output tube plate and screen ratings and re-check the bias afterward. A 5R4 does the opposite and drops B+ a little.
- Current rating. The replacement’s maximum mA has to cover what the amplifier actually draws, with some margin.
- Reservoir capacitor. Every rectifier has a maximum first filter capacitor value on its datasheet, because a bigger cap means bigger charging-current peaks through the tube. Low-drop types are especially sensitive here. If someone upsized the first cap during a recap, check that it is still within the tube’s limit.
- Warm-up. Directly heated types (5U4, 5Y3, 5R4, 80) deliver B+ within a few seconds. Cathode types (GZ34, 5V4, 5Z4, 83-V and the 6.3 V tubes) take longer and bring B+ up gently, which is easier on filter caps and on cold output tubes.
- Pinout. The 5X4 and 5Y4 are electrically a 5U4 and a 5Y3 but have different pin connections. The 5Z3, 80 and 83-V need a 4-pin to octal adapter. The 6004 has its plates on top caps. Tubes marked ‡ have extra internal connections, so make sure nothing is wired to the socket’s unused pins.
- Mercury vapor (83, 82). Let the heater run for at least 30 seconds before applying plate voltage, and mount the tube upright. These tubes can also radiate RF hash, which shows up as buzz in nearby circuits.
Table data adapted from Mike’s (MDBVentures) full-wave rectifier list, with corrections and additions by Tube Maze.
