Rectifier Tube Bases and Pinouts

Two rectifiers can share the same octal shell and still not be interchangeable. The basing code in the tube manuals (5T, 5L, 5DA and so on) tells you which pin does what, and that decides whether a swap is a simple plug-in or a smoke test. Below are pin diagrams for the bases used by every tube in our Rectifier Tube Chart, with each tube linked straight to its specs.

How to read the diagrams

  • All diagrams are bottom views, looking at the pins the way you see them when you turn the tube over or look into the socket from under the chassis.
  • Pins are numbered clockwise from the key: the spigot key on octal, the notch on loctal, and the gap on miniature and noval bases. On 4-pin and 5-pin UX bases the two thick pins are the filament or heater.
  • f filament, h heater, a anode (plate), k cathode, h+k heater with the cathode tied to it, m internal shield, ic internal connection. Empty circles are not connected.
  • Orange pins are filament or heater, white are plates, blue is cathode.
1f2a3a4fbottom view

4C (4-pin UX)

The original four-pin base from the 1920s. The two thicker pins carry the filament, so the tube only goes in one way. Plates are on pins 2 and 3.

Tubes with this base: 5Z3, 80, 83, 83-V, 82

1h2a3a4k5hbottom view

5D (5-pin UX)

Five-pin version for an indirectly heated rectifier. The extra pin brings out the cathode, which is also where the B+ comes off. Pin spacing is drawn schematically.

Tubes with this base: 84 / 6Z4

12f34a56a78fbottom view

5T (Octal)

The standard octal rectifier base and the one most audio amps use. Filament on pins 2 and 8, plates on 4 and 6, nothing else connected. B+ comes off the filament, usually pin 8.

Tubes with this base: 5AS4-A, 5AU4, 5AW4, 5AX4-GT, 5R4-G / GY, 5R4-GYA, 5R4-GYB, 5T4, 5U4-G, 5U4-GA, 5U4-GB, 5V3, 5V3-A, 5W4-G / GT, 5Y3-G / GT, 5931

12h34a56a78h+kbottom view

5L (Octal)

Same pin positions as 5T, but the tube is indirectly heated and the cathode is tied to the heater at pin 8. That is why these plug straight into a 5Y3 socket: the socket sees the same heater and plate pins, and B+ still comes off pin 8. On some 5L tubes pin 1 connects to an internal shield, so check that the socket has nothing wired there.

Tubes with this base: 5AT4, 5CG4, 5V4-G / GA, 5Z4, 6087, 6106

1m2h34a56a78h+kbottom view

5DA (Octal)

The GZ34 base. It matches 5L, with the cathode tied to pin 8, plus pin 1 connected to an internal shield (m). Leave pin 1 unconnected. If an amp uses the empty pin 1 of its 5U4 or 5Y3 socket as a tie point, a GZ34 is not a safe plug-in until that wire is moved.

Tubes with this base: 5AR4 / GZ34

1m2h3a45a67h8kbottom view

6S (Octal)

Octal base for 6.3 V rectifiers with a separate cathode on pin 8. The heater is on pins 2 and 7, plates on 3 and 5, so it is wired completely differently from a 5Y3 even though it fits the same socket.

Tubes with this base: 6AX5-GT, 6W5-G, 6X5, 6ZY5-G, 5852

gap1a23h4h56a7kbottom view

5BS (7-pin miniature)

The small 7-pin rectifier base. Heater on 3 and 4, plates on 1 and 6, cathode on 7. Pins are numbered clockwise from the gap.

Tubes with this base: 6X4, 6202, 12X4

gap1a2ic3k4h5h6ic7a8ic9icbottom view

9M (9-pin noval)

Noval base of the EZ81. Pins 2, 6, 8 and 9 are internal connections. Use them for nothing, not even as tie points.

Tubes with this base: 6CA4

1h23a456a7k8hbottom view

5AB (Loctal)

Loctal (lock-in) base, found in Philco and other radios of the 1940s. The metal spigot has a notch that sets the orientation and holds the tube in the socket.

Tubes with this base: 7Y4, 7Z4

Other Bases in the Chart

These bases are used by compactrons, series-string radio rectifiers and a few special types. Check the data sheet for the pinout before you wire a socket for any of them. The 5Q tubes deserve a special mention: they use an ordinary octal shell but a different pinout from the 5T, so a 5X4 or 5Y4 will not work in a 5U4 or 5Y3 socket.

Basing codeTubes
5Q5X4-G, 5X4-GA, 5Y4-G / GT
12BR5AZ3
9QJ5BC3
8KS5DJ4
2AJ6004
8HE6853
7Q6AX6-G, 25X6, 25Z6, 50AX6-G, 50Y6, 117Z6
9DJ6BW4, 12BW4
6CN6BY5-G / GA
6K6Z5
9CD6203
9ET6754
4R0Z4
5DE3DG4
9BS12DF5, 26Z5
6E25Y5, 25Z5
7AJ50X6
8AN50Y7, 50Z7
7B50Z6
6BJ28Z5
Loctal, code not confirmed5AZ4
Noval, code not confirmed5993
Not listed6325, 5690

Once you know which base you are dealing with, the Rectifier Tube Chart covers the rest: heater current, voltage drop, current rating and the swap rules.

Share this post:

Leave a Reply

Your email address will not be published. Required fields are marked *